80 type flat aluminum-plastic packaging machine parameters and operation

    Flat aluminum-plastic packaging machine product parameters:

Aluminum plastic packaging machine operating procedures:

1. The green indicator light is on, and the heating switch is formed up and down and heat-sealed respectively to open the operating position. The temperature controller controls the forming temperature, generally preset to 100oC, the second temperature controller controls the heat seal, and the temperature preset is 130oC~140oC. The upper and lower molding and heat sealing temperature controller preset temperature, depending on the situation.

2, put down the pressure block on the feeding roller, the temperature of the forming heating plate is in place, and then open the main machine, the plastic PVC is first formed, the forming blister is in conformity with the hole position of the heat sealing mold, pay attention to the heat sealing mold cylinder and put down the heat sealing mold to press the aluminum foil. The aluminum foil will drive to the punch. Observe whether the plastic (referred to as the machine surface has been formed PVC) travels left and right offset. If there is a bias, the direction of the pressure roller should be adjusted.

3. If the aluminum foil is tilted left and right, the adjustable turning roller seat hand wheel is adjusted. If the front and rear deviations are adjustable, the box moves.

4. After the heat seal is normal, open the feeder switch and the gate properly, so that the medicine (tablet capsule, grain clothing) enters the feeding room in an appropriate amount. If there is a small amount of cylinder material, it can be manually filled. If the medicine is brought into the heat, When sealing the mold, it will seriously affect the synchronization. Therefore, when the aluminum foil is sealed, it should be stuck on the mold and it should be stopped.

5, due to increased drug weight, aluminum foil tension and machine temperature gradually varying degrees, may cause molding and heat sealing is not synchronized, leading or lagging, first check whether plastic PVC and aluminum foil have a negative separation, and then can be adjusted by fine adjustment mechanism on the machine. The fine adjustment mechanism adjusts the distance or the front and rear adjustment of the cabinet as the mold moves forward and backward. As shown in Figure (2), it should be placed in the neutral position before starting, so that it can be moved forwards and backwards. It can also be adjusted by moving the front box. After correct movement, the plate will not be correct until after a dozen versions have been completed, so it is not taken. When you are finished, don't mess around and adjust.

6, plastic, aluminum foil heat-sealing quality (bonding uniform and firm) by temperature or pressure, the relief of the screen plate to see, if there is a bad heat seal, generally suitable temperature, pressure is slightly lower, the regulator is positive temperature, Zui Adjust the screw pressure afterwards.

7. Punching the offset, cutting the layout offset, see Figure (3). When the machine stops, the hand is moved to the box, and the mode shift can be adjusted.

8, in the daily operation knowledge, must understand the structural principle of the machine for the operation work, the roller of the cam drive ejector seat, the up and down stroke, the upper cover template position is fixed dead, the blister is in a bad state, pay attention to the lower forming die or heat seal To the top dead center, fasten the column nut, if it is not careful, it will be easy to malfunction, and the roller needle will be bitten by the plunger.

Food Additives

Food additive is indispensable in food, food manufacturers need to add the food additives in the production process, in order to change the food color, smell, or adjust the taste of food, and for a time, such as Preservatives and antioxidants, and Sweeteners, such as these are most of food additives, plant extracts, through professional technology of extraction, There are many kinds of food additives, mainly: preservatives, colorants, sweeteners, spices, leavening agents, acidity regulators, antioxidants, thickeners, emulsifiers and Food Additives,Tbhq Active Ingredients Powder,Custom Citric Acid,Useful Plant Extractpowers so on.

Food Additives,Tbhq Active Ingredients Powder,Custom Citric Acid,Useful Plant Extractpowers

Xi'an Henrikang Biotech Co.,Ltd , https://www.xianhenrikangbio.com